{"id":3914,"date":"2020-06-28T10:32:37","date_gmt":"2020-06-28T16:32:37","guid":{"rendered":"http:\/\/www.velocity-xl.com\/blog\/?p=3914"},"modified":"2020-06-28T10:32:37","modified_gmt":"2020-06-28T16:32:37","slug":"12-99-engine-induction-air","status":"publish","type":"post","link":"https:\/\/www.velocity-xl.com\/blog\/2020\/06\/28\/12-99-engine-induction-air\/","title":{"rendered":"12.99 Engine induction air"},"content":{"rendered":"
This entry is part 50 of 50 in the series 12 - Engine \/ Propeller<\/a><\/div><\/div><\/div>

My CHT’s (Cylinder Head Temperature) run hot.\u00a0 This is not an unknown issue with a Velocity.\u00a0 Keeping CHT’s in a manageable is an ongoing challenge with many piston engine aircraft.\u00a0 Since the engines are air cooled, getting air to flow around the cylinders is key.<\/p>\n

So here’s the Velocity engine setup for a Continental IO550 engine.<\/p>\n

\"IO550<\/a><\/p>\n

Air enters the upper plenum through the two roof NACA Ducts (upper right of diagram).\u00a0 This air then moves down around the six cylinders cooling them (and also passes through the oil cooler) on its way to the lower plenum. The lower plenum air is the exhausted through the openings at the rear of the cowling in front of the propeller.<\/p>\n

My configuration has one difference.\u00a0 The engine exhaust is routed aft out the bottom of the lower cowling with fairings around each of the two exhaust pipes.\u00a0 This is another exit point for the hot, lower plenum air. This should provide better cooling than the standard setup where the exhaust sticks straight down out the lower cowling.<\/p>\n

\"IO550<\/a><\/p>\n

One of the first things airplane owners do when faced with high CHT’s is to find and plug any holes in the baffling separating the upper and lower plenum. Those openings will allow cooling air to escape into the lower plenum.\u00a0 I checked and plugged any holes and made sure there were no large gaps between the baffles and the cylinders.<\/p>\n

Now what?<\/p>\n

Normally, people look at trying to get more air into the upper plenum.\u00a0 On a Velocity this can be a challenge that traditional tractor style aircraft don’t have to worry about. On your typical Cessna, Piper or Beechcraft, the upper plenum entrance is at the front of the airplane and it’s wide open. Not so on the Velocity.\u00a0 Some builders have installed vortex generators on the roof to keep the air attached to the top of the fuselage making it easier to get into the NACA Ducts on the roof.\u00a0 Some of these VG’s are so big they look like shark fins.<\/p>\n

One of the things my good friend Malcolm Collier taught me was to think of cooling air like a length of rope; It’s a lot easier to pull rope out of a space than it is to push it into a space.\u00a0 If you pull\u00a0enough air\u00a0out of the lower plenum, then more cooling air will have to be drawn into the upper plenum (assuming the openings are large enough and there’s no blockage).\u00a0 To that end, some builders have installed vents on the bottom to provide additional exits for the hot air. But I already had that with my exhaust. I could add these louvers, but I don’t think that’s the solution.<\/p>\n

Clearly there’s something else.<\/p>\n

The Continental IO550 engine installation in a Velocity is somewhat unique. The induction air intake is unfiltered. While building, I started building a pipe to connect the intake to the lower plenum which would connect to a filter box that was then connected to an intake scoop or duct.\u00a0 But the space was just too tight and by this point the modifications had piled up and I needed to finish the build and get in the air.\u00a0 So I elected to stick with the plans.\u00a0 I did build a small U-turn so the air was being pulled from the front instead of the back.<\/p>\n

\"2014-08-18<\/a><\/p>\n

Then one day during a short, local flight I noticed that I wasn’t fighting to keep my CHT’s down in the climb.\u00a0 And in cruise they were much lower than usual. Once back on the ground, I discovered that the oil door was open.\u00a0 I’m guessing that it wasn’t pressed all the way down and it popped open once the engine started. But why would that result in lower CHT’s?<\/p>\n

Here’s my theory.\u00a0 The oil door is located forward of the engine air intake.\u00a0 I think that the open oil door provided a second air source which went mostly into the engine intake.\u00a0 With the oil door opening providing induction air, that left more NACA air available for cooling.<\/p>\n

\"IO550<\/a><\/p>\n

A quick, back of the napkin calculation showed that the engine consumes about 6.5 cu\/ft of air every second.\u00a0 Which means that 6.5 cu\/ft per second of cooling air coming in the roof NACA ducts is being consumed by the engine.\u00a0 Now I don’t know how to calculate the volume of air coming through the two roof NACA’s.\u00a0 But every cu\/ft would matter.<\/p>\n

Now the question is how to fix it.<\/p>\n

I’m already in paint. So I would really like to not mess with the cowling.\u00a0 But I’ve got to create an opening for the engine air.\u00a0 I thought about making an oil door with a small scoop that fed a square duct on the underside of the upper cowling that then connected to the intake.\u00a0 But the fuel distribution lines are about an inch from the inside of the cowling. The other problem with that is a scoop sticking up into the air just in front of the prop would disturb the air even more than is already is.<\/p>\n

So it would have to be a small NACA duct that terminates just above the intake.\u00a0 My old “U-turn” intake would have to be replaced with a box-type of intake that would accept the air from the NACA duct.<\/p>\n

First order of business is to build the new airbox.\u00a0 Just like the original U-turn intake, I started with blue foam.\u00a0 Cut the basic shape on the bandsaw and then using Permagrit files I got it down to the shape I wanted.<\/p>\n

\"IMG_20200407_143418\"<\/a> \u00a0 \u00a0\"IMG_20200407_143443\"\"IMG_20200408_091254\"<\/a>\"IMG_20200408_091248\"<\/a>\"IMG_20200408_091243\"<\/a><\/p>\n

After a test fit, I\u00a0had to create a couple of… divots to clear engine case bolts and screws from the aluminum baffle at the rear of the engine.<\/p>\n

\"IMG_20200408_091232\"<\/a><\/p>\n

Then the whole thing gets wrapped in duct tape and a few layers of BID to create the final product. Once the epoxy has cured, I poured lacquer thinner down the opening to dissolve the blue foam. Then I just pulled out the duct tape.\u00a0 The first test fit of the new airbox revealed a problem that I ALWAYS discover: I make the foam blank the size I want the finished piece!\u00a0 Which means it a little too big.\u00a0 So rather than remake the whole part, I just ground out the divots and made them a little deeper.<\/p>\n

\"IMG_20200414_095128\"<\/a><\/p>\n

Then I began sanding and filling to make it pretty.\u00a0 Because that’s how I roll.<\/p>\n

Now that the airbox is done, it’s time to start on the duct. Because the engine intake is 2.75″ in diameter, that’s a little less than 6 square inches in area.\u00a0 So I will want the NACA duct to have at least that large of an opening.\u00a0 I decided on 4-1\/2″ x 1-3\/8″.\u00a0 That gives me a little under 6.2 square inches of area.<\/p>\n

Andy Millin’s Excel spreadsheet was used to determine the shape of the duct.<\/p>\n

I laid out three layers of BID on a waxed piece of glass. These would be the sides of the duct.\u00a0 Then\u00a0I determined where the end of the duct should be and applied masking tape to the cowling and drew out the duct.<\/p>\n

 <\/p>\n

\"IMG_20200423_095100\"<\/a><\/p>\n

I cut the back and sides of the duct and left the front of the ramp attached.<\/p>\n

\"IMG_20200423_101914\"<\/p>\n

The side pieces of the duct where cut so that they would be too high.\u00a0 I slid them into the cuts for the side of the duct (I used three layers of BID because it was the exact thickness of the saw blade I used to cut the duct). Stir sticks cut to 1-3\/8″ long were used to hold the ramp at the correct angle while the epoxy holding the sides to the cowling and duct ramp cured.<\/p>\n

\"IMG_20200424_082410\"<\/a>\"IMG_20200424_082438\"<\/a><\/p>\n

Once the epoxy cured, I trimmed the top and bottom of the side pieces.\u00a0 I left them longer on the back to create the channel that would feed the airbox. I rounded the bottom side of the duct and applied a few layers of BID to reinforce the duct. On the topside, I used epoxy\/cabo to create a small fillet at the bottom of the ramp. While all of that was setting up, I used some leftover fiberglass to create the front and back of the air channel.\u00a0 Then that was wrapped with BID as well.<\/p>\n

\"IMG_20200502_161549\"<\/p>\n

After everything had cured, I began sanding, filling, sanding, filling sanding, priming, sanding, filling, sanding, priming… You get the idea. Eventually, it was time to paint. Before that, I did a test fit just to make sure the new duct didn’t interfere or hit anything on the engine.<\/p>\n

I was going to paint\u00a0it myself, but I figured that I would have the guy who painted the lower nose after the front gear sheared off take care of that task. Couple days later, the cowling was done.<\/p>\n

Now it was time to figure out how to interface the duct channel with the airbox.\u00a0 When I started all of this, to allow the duct channel to be able to move in and out of the airbox and also move left\/right and front\/back, I was thinking of using baffle material as a sleeve.\u00a0 \u00a0But the number of parts and complexity became too much.\u00a0 Add to that, there would be very little left\/right and front\/rear motion because of where this interface is located. And that it didn’t need to be perfectly airtight.\u00a0 So I decided to use flexible baffle material to make the interface as airtight and simple as possible.<\/p>\n

I mounted the new airbox, installed the cowling (as far as it would go) and marked the airbox where the duct channel hit it. Then I cut a rectangular opening on the top of the airbox.\u00a0 Put the cowling back on, see where it hits, enlarge the opening, repeat about a half dozen times that now the duct channel slips inside the airbox opening. To be honest, this is probably good enough.\u00a0 I have about 1\/4″ gap on the sides and 1\/8″ on the front and rear.\u00a0 For now, I’m going to fly with it like this.\u00a0 Then once I’m certain there’s no contact between the NACA runner and the airbox, I’ll revisit the interface again.<\/p>\n

One thing that was bothering me about this setup is water.\u00a0 I remember Malcolm telling me about a guy who put an induction air scoop on the bottom of the cowl (Lycoming engine, as I recall).\u00a0 One day he was trying to takeoff on a wet runway and the engine kept losing power during the takeoff roll. After a number of attempts, he gave up.\u00a0 Turned out that water was being kicked up by the nosewheel was being ingested into engine significantly reducing power.\u00a0 He ended up moving the intake duct off to the side didn’t have any further problems.<\/p>\n

So I’m curious if I fly through some really heavy rain will I run into any problems. I asked a couple IA’s and they said if I flew through rain heavy enough to affect the engine performance that I had would be having other more significant issues before the engine became a problem.\u00a0 Okay… but where to get a more expert opinion?<\/p>\n

George Braly is an engine guy who really knows engines. He’s one of the three guys who started GAMI<\/a> and\u00a0Tornado Alley Turbo<\/a>. \u00a0We had a chat unrelated to Velocity’s almost 20 years ago.\u00a0 So I reached out and asked him.\u00a0 He said that he had run some calculations at one point and that heavy rain shouldn’t be able to introduce enough water as to affect engine operations. He also wasn’t a fan of NACA ducts.\u00a0 But that donkey was already out of the barn.\u00a0 But his feeling about the water was good enough for me… Kinda.<\/p>\n

I remember my old IA telling me how the intake on a Cessna Caravan works.\u00a0 The air intake is actually at the back of the engine.\u00a0 The air enters a duct just behind the prop.\u00a0 Travels all the way to the back of the engine and then makes a 180 degree turn and enters the turbine inlet. If they are taking off from an unimproved runway or in situations where lots of… non-air material is entering the duct, they can open a door at the 180 turn so that heavy material will continue out the back while the (lighter) air makes the 180 degree turn into the engine.<\/p>\n

So here’s what I’m thinking: The airbox slopes away from the engine intake.\u00a0 I’ll drill some holes at the lowest point in the airbox.\u00a0 Any excessive water will drain out the airbox while the lighter air will make the 180 degree turn into the engine intake. I’d really like a door that I can open, but that’s a long way to run that cable.\u00a0 And I’ve already got three control levers besides the engine controls in the cabin (heated air damper, oil cooler damper and parking brake) so I don’t one more to have to find a place for.<\/p>\n

Finished airbox painted the same color as the engine.<\/p>\n

\"IMG_20200512_075412\"<\/a><\/p>\n

Installed on the engine.<\/p>\n

\"IMG_20200601_070630a\"<\/p>\n

Cowling installed<\/p>\n

\"IMG_20200506_125344\"IMG_20200506_125254<\/a><\/p>\n

I was able to go up the other day.\u00a0 Unfortunately, because of the Saharan dust cloud I couldn’t get over 2,500′ so I had to pull the power back and descend to 2,000′ with the power pulled back so I don’t have a good “apples to apples” comparison flight (normally when I takeoff the power stays all the way in until I hit cruising altitude).\u00a0 But looking at a past flight with the OAT 15F cooler and the engine oil cooler damper closed (providing more cooling air for the cylinders and induction), my #2 CHT hit 412F on that flight. On my latest flight the OAT was 15F hotter, the oil cooler damper was open and my #2 CHT only hit 397F.\u00a0 I’m think that with the damper closed that I would have dropped that temp at least 10 to 15 degrees.<\/p>\n

So for now, I’m calling this a win.\u00a0 Once this dust clears out I’ll be able to get some additional data.<\/p>\n","protected":false},"excerpt":{"rendered":"

This entry is part 50 of 50 in the series 12 - Engine \/ Propeller<\/a><\/div><\/div><\/div>

My CHT’s (Cylinder Head Temperature) run hot.\u00a0 This is not an unknown issue with a Velocity.\u00a0 Keeping CHT’s in a manageable is an ongoing challenge with many piston engine aircraft.\u00a0 Since the engines are air cooled, getting air to flow … Continue reading →<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":false,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[53],"tags":[],"series":[36],"class_list":["post-3914","post","type-post","status-publish","format-standard","hentry","category-53","series-12-engine-propeller"],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/3914","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/comments?post=3914"}],"version-history":[{"count":9,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/3914\/revisions"}],"predecessor-version":[{"id":3965,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/3914\/revisions\/3965"}],"wp:attachment":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/media?parent=3914"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/categories?post=3914"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/tags?post=3914"},{"taxonomy":"series","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/series?post=3914"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}