{"id":428,"date":"2011-01-06T17:05:15","date_gmt":"2011-01-06T23:05:15","guid":{"rendered":"http:\/\/www.velocity-xl.com\/blog\/?p=428"},"modified":"2015-02-15T14:28:40","modified_gmt":"2015-02-15T20:28:40","slug":"top-side-finish","status":"publish","type":"post","link":"https:\/\/www.velocity-xl.com\/blog\/2011\/01\/06\/top-side-finish\/","title":{"rendered":"14.2.1 Top side finish"},"content":{"rendered":"
This entry is part 13 of 38 in the series 14 - Final Assembly \/ FInishing<\/a><\/div><\/div><\/div>

Since we’re now working on the tops of the wings (where they will be easy to view (as opposed to the underside)) it’s important that they are as close to perfect as we can get them. We already did some extensive sanding and removed a bunch of unnecessary filler, but there are still some low spots. And Malcolm (ever the perfectionist) wasn’t happy with my strake-wing joints.<\/p>\n

So first we located (again) the low spots and marked them. Then we put in the aluminum “dams” that Malcolm uses to retain and improve the joint.<\/p>\n

Here’s a picture of the pilot side strake\/wing with the aluminum in place
\n\"\"<\/a><\/p>\n

Same side from the back.
\n\"\"<\/a><\/p>\n

CoPilot side.
\n\"\"<\/a><\/p>\n

The gap along the back was really high so we knew there’d be no filler going on there.<\/p>\n

Right wing with low spots marked.
\n\"\"<\/a><\/p>\n

Then it’s time to add the Resin Research resin and microballoon.<\/p>\n

Right wing with a layer of filler.
\n\"\"<\/a><\/p>\n

At the wing\/strake joint
\n\"\"<\/a><\/p>\n

Right wing aft of the strake.
\n\"\"<\/a><\/p>\n

While I thought the doors were fine (especially compared to how they were), they still weren’t “good enough”. So some fill had to be added around the upper\/aft edge of the co-pilot door.
\n\"\"<\/a><\/p>\n

Here’s the pilot side wing-strake joint.
\n\"\"<\/a><\/p>\n

And then the filler has to be sanded down. \ud83d\ude41
\n\"\"<\/a>\"\"<\/a><\/p>\n

But now the tops of the wings and strakes are as good as they can be made until we get some primer on it. Once the surface is is close to being smooth but in full “spotted dog” mode, the variations in texture make it difficult to determine if you’re feeling a low spot or a change in surface texture. So once the entire surface is primed, we’ll block it out and see if there are anymore low or high spots. Until then, there not much more to do with the wings.<\/p>\n","protected":false},"excerpt":{"rendered":"

This entry is part 13 of 38 in the series 14 - Final Assembly \/ FInishing<\/a><\/div><\/div><\/div>

Since we’re now working on the tops of the wings (where they will be easy to view (as opposed to the underside)) it’s important that they are as close to perfect as we can get them. We already did some … Continue reading →<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":false,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[8],"tags":[],"series":[38],"class_list":["post-428","post","type-post","status-publish","format-standard","hentry","category-8","series-14-final-assembly-finishing"],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/428","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/comments?post=428"}],"version-history":[{"count":4,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/428\/revisions"}],"predecessor-version":[{"id":3208,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/posts\/428\/revisions\/3208"}],"wp:attachment":[{"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/media?parent=428"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/categories?post=428"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/tags?post=428"},{"taxonomy":"series","embeddable":true,"href":"https:\/\/www.velocity-xl.com\/blog\/wp-json\/wp\/v2\/series?post=428"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}