- 13.4.3 Pitot Tube Installation
- 13.4.2 Static Port
- 13.2.1 Instrument Panel Mounting
- 13.3.2 Ground Power Plug
- 13.0 Electrical System Documentation
- 13.0 Wire Labels
- 13.2.2 / 13.6.2 Aft wiring complete
- 13.8.1 Magnetometer connections
- 13.9.2 Autopilot Roll Servo Wire Routing Modification
- 13.7.1 Avionics Shelf
- 13.8.1 Magnetometer Mounting Bracket – Completed
- 13.8.1 Magentometer Bracket
- 13.1.6 Transponder Antenna Ground Plane
- 13.5.1 Navigation/Strobe Wing Root Connectors
- 13.0 Electrons are flowing
- 13.9.2 Autopilot Roll Servo Mounting
- 13.3.4 Overhead Switch Panel Wiring
- 13.2.2 Engine Wiring
- 13.6.2 Primary Alternator Connection
- 13.7.1 Avionics Shelf
- 13.8.1 OAT probe
- 13.2.2 EIS wiring
- 13.2 EFIS and Instrument Panel Layout
- 13.6 Ground Block – Part II
- 13.7.4 Headset jacks
- 13.3.4 Overhead Switch Panel
- 13.6 Ground blocks
- 13.8.2 Annunicator Panel
- 13.8.2 Annunicator Panel
- 13.8.2 Annunicator Panel
- 13.6 Electrical supply lines
- 13.6.3 Ground Power Receptacle
- 13.2 Instrument Panel Layout
- 13.3.5 Avionics Wiring
- 13.9.2 Auto Pilot Pitch Servo Mounting
- 13.7 Avionics and Wiring
- 13.7 Wiring
- 13.2 Panel painting
- 13.2 Panel installation
- 12.3.5 Minor setback on Avionics wiring
- 13.8.2 Annunciator Panel Problem
- 13.1.9 ELT Installation
- 13.6 Power Supply
- 13.7.4 It’s always something…
- 13.0 Wire routing
- 13.1.8 GPS Antenna Shelf
- 13.7.4 Audio Panel Relocation
- 13.0 Wire Routing (Remediation)
- 13.6.1 Battery Hold-Down
- 13.2.1 Instrument Panel – Final Install
- 13.3.3 / 13.5.3 Trim & Landing Light Test
- 13.8.1 EFIS alternate power
- 13.5.2 Cabin Lighting
- 13.1.4 Glideslope Antenna
- 13.3.4 Overhead Switch Panel
- 13.99 Instrument Panel overlays
- 13.99 Installing Engraved parts
- 13.99 Instrument Panel Lighting
- 13.4 Pitot/Static Remediation
- Static Port Conundrum
- GPS Replacement
- Secondary EFIS Power
- 13.99 Electrical System Diagram
- 13.99 – Current Sensor Repair
- 13.99 – ADS-B in antenna
- 13.99 – Switch panel update
- 13.4 – More Static Port Fun
Normally when I create these posts, I use the section number from the manual at the beginning of the title, i.e. “7.8.4 Main Gear Microswitches”. But the electrical system is not really part of the build manual. Chapter 13 is basically “install the electrical system”. 🙂 So lately I’ve been taking the easy way out and using 13.99 for the section number. But I don’t like that since it makes it harder to find posts on a particular topic. And I think that’s very important. So I’ve expanded on the section numbers for Chapter 13. It’s a work in progress so it will probably grow as I continue working. But for now…
13.1Â Â - Antennas 13.1.4 - Glideslope Antenna 13.1.5 - Marker Beacon 13.1.6 - Transponder 13.1.8 - GPS 13.1.9 - ELT 13.2Â Â - Instrument Panel 13.2.1 - Instrument Panel 13.3Â Â - Electrical System Completion 13.3.1 - Introduction 13.3.2 - Basic Electrical System 13.3.3 - Trim, Speed Brake, & Speed Brake Warning 13.3.4 - Switches and Circuit Protection 13.3.5 - Avionics 13.3.6 - P-Leads 13.4Â Â - Pitot - Static and Vacuum Instruments 13.4.1 - Vacuum System 13.4.2 - Static Port 13.4.3 - Pitot Tube 13.5Â Â - Lighting 13.5.1 - Nav/Strobe Lighting 13.5.2 - Cabin Lighting 13.5.3 - Landing Lights 13.6Â Â - Power Distribution 13.6.1 - Battery 13.6.2 - Alternator 13.6.3 - GPC 13.6.4 - Starter 13.7Â Â - Avionics 13.7.1 - Avionics Shelf 13.7.2 - Radios (Navigation, Communications, Transponder) 13.7.3 - GPS 13.7.4 - Audio 13.8Â Â - Instrumentation 13.8.1 - EFIS 13.8.2 - Master Warning Annunicator 13.8.3 - EIS 13.9Â Â - Control 13.9.1 - Trim 13.9.2 - Autopilot